High-Reach Lift Services in Houston, TX
Silverheels Construction handles high-reach lift work across the Houston area — boom and scissor lift jobs for the things ladders can't safely reach. We mount, anchor, and remove signs, banners, and awnings, and do high-reach painting and repairs. We don't do any wiring or illuminated-sign hookups — mounting and removal only. Free estimates.
Get a free estimate
Tell us about your project — it takes under a minute.
- 1Service
- 2Your info
- 3Project
- 4Review
High-reach lift services in Houston cover the work that starts where a ladder stops being safe — signs two and three stories up, banners across a storefront, awnings over an entrance, and repairs on walls and eaves you can't reach from the ground. We bring the boom or scissor lift, the fall protection, and the mounting hardware to get it done. One line to be clear on up front: our sign, banner, and awning work is mounting, anchoring, and removal only. We don't touch wiring, illuminated-sign hookups, or light fixtures of any kind — that's electrical work, and it's not what we do.
Aerial lift work — boom and scissor lifts
The right lift depends on the reach and the ground. As an aerial lift contractor we run scissor lifts for straight-up vertical work on a flat, stable surface — interior high walls, ceilings, and storefronts you can drive to. Boom lift services cover the harder reaches: up and over an obstacle, out across a canopy, or to a height and angle a scissor lift can't manage.
Working at height is as much about safety as reach — fall protection, spotting, and a lift set up on ground that can actually hold it. We handle the setup and the harnesses, and we plan the positioning so the work gets done without putting anyone or your property at risk. If the job is simply too high or too awkward for a ladder, the lift is the safe way to reach it.
Hanging sign and blade sign installation
Mounting a sign up high is a lift job and an anchoring job. We handle hanging sign installation, blade sign installation, and larger storefront and building signs — including 40-ft sign installation where the mount is two or three stories up — bringing the lift, setting the brackets into solid backing, and hanging the sign level and secure.
The scope is the mounting and anchoring: getting the sign up there and fastened so it holds through Houston wind. Here's the hard line — we do not do the electrical. No wiring, no illuminated-sign hookup, no connecting a lit or channel-letter sign to power. If your sign needs to light up, the electrical connection is a separate trade; we set and anchor the sign itself, and the hookup is arranged separately from us.
Banner and awning installation
Banner installation is quick, high, and all about a clean, tight mount — we hang storefront and building banners from the lift, anchor the grommets and brackets into solid backing, and pull them taut so they don't flap or sag in the wind. Seasonal banner up, seasonal banner down; we handle both.
Awning installation, on our end, is the mounting side: fastening the awning frame and cover to the building, anchored into solid structure so it holds. To keep the scope clear — this is the mechanical mounting and anchoring only. We don't do any wiring or lighting, so a motorized or illuminated awning's electrical is not part of our work; we hang and anchor the structure, and anything electrical is handled separately.
Elevated sign removal
Signs come down as often as they go up — a business closes, rebrands, or moves, and the old sign has to come off the building, usually from the same height it went up at. Elevated sign removal is a lift-and-unfasten job: we bring the lift, take the sign down safely, remove the brackets, and haul the sign off.
We also patch the mounting points where we can — filling and sealing the holes left in the wall so the facade isn't left pocked and open to water. If the sign was illuminated, note that any disconnection from power is an electrical step handled by others before we pull the sign; our part is the mechanical removal and the cleanup of the mounting once it's de-energized.
High-reach painting and hard-to-reach repairs
A lot of high-reach work is just ordinary work that happens to be twenty feet up. High-reach painting covers tall interior walls, warehouse and atrium ceilings, exterior upper stories, and stairwells — the surfaces a roller on a pole can't do justice. From the lift we can prep and paint them properly instead of stretching off a ladder.
Hard-to-reach repairs are the same idea: soffit and fascia work up high, patching and sealing on upper walls, replacing a stretch of trim over an entrance, or getting to eaves and overhangs that a ladder can't safely reach. If the obstacle is height and access rather than the task itself, the lift turns an unsafe job into a routine one.
What we don't do up there — the electrical line
It's worth stating plainly, because it's the most common question on sign and awning work: we do not do any electrical, at any height. No wiring. No illuminated-sign hookup or channel-letter connections. No light fixture replacement of any kind — not the light over a sign, not any fixture, none of it.
What we do is the mechanical side: mounting, anchoring, and removing signs, banners, and awnings, and high-reach painting and repairs. If a job involves getting a fixture or a lit sign connected to power, that electrical portion is a separate trade arranged separately from us — we handle everything up to the point where wire meets power, and not past it. Keeping that line clear is how we keep the work safe and in our lane.
Frequently asked questions
Do you install signs on a lift?
Yes — hanging signs, blade signs, and larger storefront and building signs, including mounts two or three stories up. We bring the lift, set the brackets into solid backing, and hang the sign level and secure against Houston wind. That's the mounting and anchoring; the electrical hookup for a lit sign is not something we do.
Can you connect or wire an illuminated sign?
No — we don't do any wiring, illuminated-sign hookups, or electrical connections of any kind. We set and anchor the sign itself; connecting a lit or channel-letter sign to power is a separate electrical trade arranged separately from us. Our scope is the mechanical mounting and removal only.
What's the difference between a boom lift and a scissor lift?
A scissor lift goes straight up on flat, stable ground — good for high interior walls, ceilings, and drive-to storefronts. A boom lift reaches up and over obstacles and out across canopies, to heights and angles a scissor can't. We pick the lift to fit the reach and the ground and bring the fall protection either way.
Do you hang banners and awnings?
Yes — we mount and tension storefront and building banners, and we fasten awning frames and covers, anchored into solid structure so they hold in wind. That's the mechanical mounting and anchoring only; any wiring or lighting on a motorized or illuminated awning is electrical and handled separately from us.
Can you remove an old sign from a building?
Yes — elevated sign removal is a lift-and-unfasten job: we take the sign down safely, remove the brackets, patch and seal the mounting holes where we can, and haul the sign off. If the sign was lit, disconnection from power is an electrical step done by others before we remove it.
Can you paint or repair high walls we can't reach?
Yes — high-reach painting and repairs are a big part of this: tall interior walls, atrium and warehouse ceilings, upper exterior stories, soffit and fascia, and trim over entrances. From the lift we prep and do the work properly instead of stretching off a ladder. If height is the only obstacle, the lift makes it routine.
Service areas
- The Heights
- Bellaire
- Katy
- Sugar Land
- Cypress
- Kingwood
- Pearland
- Spring Branch